Excellent 300-410 PDF Dumps With 100% ActualTestsQuiz Exam Passing Guaranted [Oct-2024]
100% Pass Your 300-410 Implementing Cisco Enterprise Advanced Routing and Services at First Attempt with ActualTestsQuiz
Cisco 300-410 exam consists of 60-70 questions and lasts for 90 minutes. 300-410 exam format includes multiple-choice and simulation questions, which test the practical skills of the candidates. 300-410 exam is conducted in English and can be taken at any Pearson VUE testing center worldwide. Candidates who pass the exam are awarded the Cisco Certified Specialist - Enterprise Advanced Infrastructure Implementation certification.
NEW QUESTION # 77
An engineer failed to run diagnostic commands on devices using Cisco DNA Center. Which action in Cisco DNA Center resolves the issue?
- A. Enable APIs
- B. Enable Command Runner
- C. Enable CDP
- D. Enable Secure Shell
Answer: B
NEW QUESTION # 78
Refer to the exhibit.
A network administrator configured mutual redistribution on R1 and R2 routers, which caused instability in the network. Which action resolves the issue?
- A. Advertise summary routes of EIGRP to OSPF and deny specific EIGRP routes when redistributing into OSPF.
- B. Set a tag in the route map when redistributing EIGRP into OSPF on R1. and match the same tag on R2 to allow when redistributing OSPF into EIGRP.
- C. Set a tag in the route map when redistributing EIGRP into OSPF on R1, and match the same tag on R2 to deny when redistributing OSPF into EIGRP.
- D. Apply a prefix list of EIGRP network routes in OSPF domain on R1 to propagate back into the EIGRP routing domain.
Answer: C
Explanation:
Explanation
https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/8606-redist.htm
NEW QUESTION # 79
Drag and drop the operations from the left onto the locations where the operations are performed on the right.
Answer:
Explanation:
NEW QUESTION # 80
Refer to the exhibit.
What does the imp-null tag represent in the MPLS VPN cloud?
- A. Impose the label
- B. Pop the label
- C. Exclude the EXP bit
- D. Include the EXP bit
Answer: B
Explanation:
Explanation
The imp-null (implicit null) tag instructs the upstream router to pop the tag entry off the tag stack before forwarding the packet.
Note: pop means remove the top MPLS label
NEW QUESTION # 81
Refer to the Exhibit.
R1 and R2 use IGP protocol to route traffic between AS 100 and AS 200 despite being configured to use BGP.
Which action resolves the issue and ensures the use of BGP?
- A. Configure distance to 100 under the OSPF process of R1 and R2
- B. Remove distance commands under BGP AS 100 and AS 200.
- C. Configure distance to 100 under the EIGRP process of R1 and R2.
- D. Remove distance commands under BGP AS 100.
Answer: B
NEW QUESTION # 82
Refer to the exhibit.
The network administrator must configure Cape Town to reach Dubai via Tokyo based on the speeds provided by the service provider. It was noticed that Cape Town is reaching Dubai directly and failed to meet the requirement. Which configuration fixes the issue?
- A.
- B.
- C.
- D.
Answer: D
NEW QUESTION # 83
A router in an EVN environment is choosing a route. Which value is given the highest selection priority?
- A. IGP administrative distance of the route
- B. lexical value of the source VRF name
- C. default administrative distance of the route
- D. replication status of the route
- E. VNET tag of the route
Answer: A
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/layer-3-vpns-l3vpn/ whitepaper_c11-638769.html
NEW QUESTION # 84
Refer to the exhibit.
An engineer wanted to set a tag of 30 to route 10 1.80.65/32 but it failed How is the issue fixed?
- A. Modify route-map ospf-to-eigrp permit 10 and match prefix-list ccnp2.
- B. Modify prefix-list ccnp3 to add 10.1.64.0/20 ge 32
- C. Modify route-map ospf-to-eigrp permit 30 and match prefix-list ccnp2.
- D. Modify prefix-list ccnp3 to add 10.1.64.0/20 le 24
Answer: A
NEW QUESTION # 85
Refer to the exhibit.
An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries. Which action ensures consistency between the two times?
- A. Configure the logging clock synchronize command in global configuration mode.
- B. Configure the service timestamps log datetime localtime command in global configuration mode.
- C. Configure the service timestamps log uptime command in global configuration mode.
- D. Make sure that the clock on the device is synchronized with an NTP server.
Answer: D
NEW QUESTION # 86
What does IPv6 Source Guard utilize to determine if IPv6 source addresses should be forwarded?
- A. ACE
- B. Binding Table
- C. DHCP
- D. ACLS
Answer: B
Explanation:
NEW QUESTION # 87
Refer to the exhibit.
After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?
- A. Set the administrative distance 100 under the RIP process on R2.
- B. Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.
- C. Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.
- D. Redistribute the directly connected interfaces on R2.
Answer: A
NEW QUESTION # 88
Refer to the exhibit.
Refer to the exhibit. An organization is installing a new L3 MPLS link to establish DM VPN Phase 2 tunnels between the hub and two spoke routers Which additional configuration should the engineer implement on each device to achieve optimal routing between the spokes?
- A.
- B.
- C.
- D.
Answer: D
NEW QUESTION # 89
Refer to the exhibit.
Refer to the exhibit. The administrator is troubleshooting a BGP peering between PE1 and PE3 that is unable to establish Which action resolves the issue?
- A. Remove the traffic filtering rules on P2 blocking the BGP communication between PE1 and PE3
- B. P2 must have a route to PE3 to establish a BGP session to PE1
- C. Ensure that the PE3 loopback address is used as a source for BGP peering to PE1
- D. Disable sending ICMP unreachables on P2 to allow PE1 to establish a session with PE3
Answer: C
NEW QUESTION # 90
Refer to the exhibit. Users report that IP addresses cannot be acquired from the DHCP server. The DHCP server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day.
Which action fixes the issue within the current resources?
- A. Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool
- B. Configure the DHCP lease time to a smaller value
- C. Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool
- D. Configure the DHCP lease time to a bigger value
Answer: B
Explanation:
Section: Infrastructure Services
Explanation
NEW QUESTION # 91
Refer to the exhibits.
Phase-3 tunnels cannot be established between spoke-to-spoke in DMVPN. Which two commands are missing? (Choose two.)
- A. The ip nhrp redirect commands is missing on the hub router.
- B. The ip nhrp shortcut commands is missing on the hub router.
- C. The ip nhrp map command is missing on the hub router.
- D. The ip nhrp redirect command is missing on the spoke routers.
- E. The ip nhrp shortcut command is missing on the spoke routers.
Answer: A,E
NEW QUESTION # 92
Refer to the exhibit.
The network administrator configured the network to connect two disjointed networks and ail the connectivity is up except the virtual link which causes area 250 to be unreachable. Which two configurations resolve this issue? (Choose two.)
- A. R2
router ospf 1
no area 234 virtual-link 10.34.34.4
area 234 virtual-link 0.0.0.44 - B. R2
router ospf 1
no area area 234 virtual-link 10.34.34.4
area 0 virtual-link 0.0.0.44 - C. R4
router ospf 1
no area area 234 virtual-link 10.23.23.2
area 0 virtual-link 0.0.0.22 - D. R4
router ospf 1
no area 234 virtual-link 10.23.23.2
area 234 virtual-link 0.0.0.22 - E. R2
router ospf 1
router-id 10.23.23.2
Answer: A,D
Explanation:
Reference:
An important thing to remember when configuring virtual-link is we need to configure the OSPF router ID and NOT the IP address of the ABR. Therefore in this question we have to use the command "area
234 virtual-link 0.0.0.44" on R2 and "area 234 virtual-link 0.0.0.22" on R4.
NEW QUESTION # 93
Refer to the exhibit.
Which subnet is redistributed from EIGRP to OSPF routing protocols?
- A. 10.2.3.0/26
- B. 10.1.4.0/26
- C. 10.2.2.0/24
- D. 10.1.2.0/24
Answer: C
NEW QUESTION # 94
An engineer configured a leak-map command to summarize EIGRP routes and advertise specifically loopback 0 with an IP of 10.1.1.1.255.255.255.252 along with the summary route. After finishing configuration, the customer complained not receiving summary route with specific loopback address. Which two configurations will fix it? (Choose two.)
- A. Configure access-list 1 and match under route-map Leak-Route.
- B. Configure access-list 1 permit 10.1.1.0.0.0.0.3.
- C. Configure route-map Leak-Route permit 20.
- D. Configure route-map Leak-Route permit 10 and match access-list 1.
- E. Configure access-list 1 permit 10.1.1.1.0.0.0.252.
Answer: B,D
Explanation:
When you configure an EIGRP summary route, all networks that fall within the range of your summary are suppressed and no longer advertised on the interface. Only the summary route is advertised. But if we want to advertise a network that has been suppressed along with the summary route then we can use leak-map feature. The below commands will fix the configuration in this question:
R1(
config)#access-list 1 permit 10.1.1.0 0.0.0.3
R1(config)#route-map Leak-Route permit 10 // this command will also remove the "route_map Leak-Route deny 10" command.
R1(config-route-map)#match ip address 1
NEW QUESTION # 95
Refer to the exhibit.
All the serial between R1, R2, and R3 have the Same bandwidth. User on the 192.168.1.0/24 network report slow response times while they access resource on network 192.168.3.0/24. When a traceroute is run on the path. It shows that the packet is getting forwarded via R2 to R3 although the link between R1 and R3 is still up. What must the network administrator to fix the slowness?
- A. Add a static route on R1 using the next hop of R3.
- B. Remove the static route on R1.
- C. Redistribute theR1 route to EIGRP
- D. Change the Administrative Distance of EIGRP to 5.
Answer: B
NEW QUESTION # 96
A network administrator is tasked to permit http and https traffic only toward the internet from the User1 laptop to adhere to company's security policy. The administrator can still ping to www.cisco.com Which interface should the access list 101 be applied to resolve this issue?
- A. Interface S1/0 in the outgoing direction.
- B. Interface G0/0 in the incoming direction.
- C. Interface G0/48 in the incoming direction
- D. Interface G0/0 in the outgoing direction.
Answer: B
NEW QUESTION # 97
Which statement about IPv6 ND inspection is true?
- A. It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables.
- B. It learns and secures bindings for stateless autoconfiguration addresses in Layer 2 neighbor tables.
- C. It learns and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables.
- D. It learns and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables.
Answer: B
NEW QUESTION # 98
Which configuration enables the VRF that is labeled "Inet" on FastEthernet0/0?
- A. R1(config)#router ospf 1 vrf Inet
R1(config-router)#ip vrf forwarding FastEthernet0/0 - B. R1(config)# ip vrf Inet
R1(config-vrf)#interface FastEthernet0/0
R1(config-if)#ip vrf forwarding Inet - C. R1(config)#ip vrf Inet FastEthernet0/0
- D. R1(config)# ip vrf Inet
R1(config-vrf)#ip vrf FastEthernet0/0
Answer: B
Explanation:
Section: Layer 3 Technologies
NEW QUESTION # 99
......
What is Cisco 300-410 ENARSI Exam
Cisco Certified Network Associate (CCNA) is an entry-level Cisco networking certification for associate-level network engineers introduced in the year 1995. It covers topics on LAN, WAN, wireless, routing and switching, services introduction including DNS, DHCP. Experience level: The candidate should have basic knowledge about networking concepts like IP addressing, subnetting, default gateway/route, and routing. List of exams: There are two exams associated with CCNA, Cisco 300-070 Interconnecting Cisco Networking Devices Part 1 (ICND1) AND Cisco 300-080 Interconnecting Cisco Networking Devices Part 2 (ICND2) 300-100 Managing Industrial Networks with Cisco Network.
Tech Target analyst firm Gartner has the following to say about the latest CCNA certification requirement changes that took effect on September 6th, 2010. Paying attention to the latest updates of Cisco certification details is more than just a good idea, it is also in your best interest. Smarter people choose to react faster to the changes in the Cisco certification industry rather than wait for them to be released by Cisco. Cisco 300-410 Dumps is available for all the candidates who are preparing for the Cisco 300-410 exam. The Cisco 300-410 exam is now part of the Associate Level Certifications.
Trend for 300-410 pdf dumps before actual exam: https://www.actualtestsquiz.com/300-410-test-torrent.html
Real Exam Questions and Answers - Cisco 300-410 Dump is Ready: https://drive.google.com/open?id=1dkRTSvbmFEgtsOnsWzORJOwT2suV5cJo
