Authentic Network Appliance NS0-521 Exam Dumps PDF - 2024 Updated
Get Prepared for Your NS0-521 Exam With Actual 67 Questions
NEW QUESTION # 15
An administrator configured an SVM with LUNs with two WWPNs per node. The administrator accidentally created a WWPN on node1that needs to move to node2. The SAN hosts use ALUA.
Based on this requirement, what must be taken offline to correct the situation?
- A. SVM
- B. Volume
- C. LUN
- D. LIF
Answer: D
NEW QUESTION # 16
What needs to be done to create a consistent Snapshot copy of a LUN without disruptions?
- A. Map the LUN to a host.
- B. Ensure that the LUN is the only one in the volume.
- C. Quiesce I/O to the LUN.
- D. Ensure that the LUN Is unmapped from the host.
Answer: C
Explanation:
To create a consistent Snapshot copy of a LUN without disruptions, it is necessary to quiesce I/O to the LUN.
This process involves pausing or temporarily stopping the input/output operations to ensure that the data is in a consistent state when the snapshot is taken. This method is crucial for maintaining data integrity and consistency in the snapshot.
For further details, refer to:
* NetApp Documentation on Snapshot Consistency
* NetApp Best Practices for Snapshot Management
NEW QUESTION # 17
Which two steps must be taken first to restore a LUN from a SnapMirror Synchronous destination? (Choose two.)
- A. Delete the relationship.
- B. Resync the relationship.
- C. Release the relationship.
- D. Initialize the relationship.
Answer: A,C
Explanation:
To restore a LUN from a SnapMirror Synchronous destination, the following steps must be taken:
* Release the relationship: This step is necessary to break the SnapMirror relationship, allowing the LUN to be restored independently.
* Delete the relationship: After releasing the relationship, deleting it ensures that there are no residual dependencies or configurations that might interfere with the restore process.
For more information, refer to:
* NetApp Documentation on SnapMirror Synchronous (NetApp) (NetApp).
NEW QUESTION # 18
Click the Exhibit button.
A customer is testing a newly installed NetApp AFF A400 all-flash HA storage system. An SVM for FCP with a LUN on Node 1 has been configured, and a server has been connected as shown in the exhibit. For testing, the engineer plans to do a storage failover of Node 1.
After the failover, what is the expected status of the marked path?
- A. Unavailable
- B. Active/Optimized
- C. Offline
- D. Active/Nonoptimized
Answer: D
Explanation:
In the scenario where a storage failover is performed on Node 1 in an HA pair, the path marked in the exhibit would becomeActive/Nonoptimized. After the failover, the LIFs from Node 1 that were activeand optimized will switch to Node 2. Paths that were previously optimized will become nonoptimized because they are now served through the partner node.
For more details, see:
* NetApp Documentation on ALUA
NEW QUESTION # 19
During maintenance of A NetApp AFF ONTAP cluster, which two steps are needed to move the SAN UFs to new nodes that are members of a portset? (Choose two.)
- A. Disable the SLM feature for the node that hosts the LIF.
- B. Remove the LIF from the portset.
- C. Disable the zoning of the LIF WWPN.
- D. Take the SAN LIF offline.
Answer: B,D
Explanation:
To move SAN LIFs to new nodes that are members of a portset during maintenance of a NetApp AFF ONTAP cluster, you should take the following steps:
* Remove the LIF from the portset: This ensures that the LIF is no longer associated with the current node, preparing it for the move to the new node.
* Take the SAN LIF offline: This step is necessary to make configuration changes without causing disruption to the SAN hosts. Once offline, the LIF can be moved to the new node and reconfigured as needed.
These actions help maintain the integrity and performance of the SAN environment during the migration of LIFs.
For more details, see:
* NetApp Documentation on Moving SAN LIFs
* NetApp Community on Moving LIFs
NEW QUESTION # 20
What connectivity Is required between NetApp ONTAP clusters in order to configure SnapMirror active sync across two data centers for FC?
- A. Dedicated IP switches and ISL
- B. Shared FC switches
- C. Cluster peering
- D. Cedicated FC switches and ISL
Answer: C
Explanation:
To configure SnapMirror active sync across two data centers using FC (Fibre Channel), the required connectivity between NetApp ONTAP clusters is cluster peering. Cluster peering involves establishing a trust relationship between the clusters, allowing them to replicate data seamlessly. This setup ensures that data synchronization and disaster recovery processes are effective and reliable.
For more detailed information, you can check:
* NetApp Documentation on SnapMirror and Cluster Peering
NEW QUESTION # 21
A storage engineer in SAN environment needs to Identify FC ports using the company-wide naming policy.
Which command will accomplish this task?
- A. network interface modify
- B. ucadmin modify
- C. TCP portname set
- D. vserver fcp wwpn-alias set
Answer: D
Explanation:
The vserver fcp wwpn-alias set command is used to set or modify the World Wide Port Name (WWPN) aliases for Fibre Channel (FC) ports in a NetApp ONTAP environment. This command allows you to apply a company-wide naming policy to FC ports, ensuring consistent and easily identifiable naming conventions across your storage infrastructure.
For further details, you can refer to:
* NetApp Documentation on FC Management
* NetApp Community Discussion on WWPN Aliases
NEW QUESTION # 22
A customer has a 10GB volume with an 8GB LUN that is using 7GB. The snapshot policy is hourly and retains 48 snapshots. After a ransomware attack that encrypts all files on the LUN, the customer notices that all snapshots are gone.
What could cause this behavior?
- A. Snapshot autodelete
- B. Autonomous Ransomware Protection
- C. Volume thinly provisioned
- D. Aggregate overcommitted
Answer: A
Explanation:
The likely cause for the disappearance of all snapshots after a ransomware attack that encrypted all files on the LUN is the Snapshot autodelete feature. When the volume becomes full due to the encryption, the autodelete feature removes older snapshots to free up space, preventing the volume from running out of space and ensuring write operations can continue.
For more information, see:
* NetApp Documentation on Snapshot Autodelete
* NetApp Community Discussion on Snapshot Deletion
NEW QUESTION # 23
An administrator finishes an installation of a new NetApp ASA system at the customer site and creates a new LUN. The customer wants to restrict the access of the LUN to specific UFs.
Where would the administrator configure this?
- A. Zoning
- B. Selective LUN Map
- C. igroup
- D. Portset
Answer: C
Explanation:
To restrict access to a newly created LUN to specific hosts, the administrator should configure theigroup (initiator group). An igroup is used to control which initiators (hosts) are allowed to access specific LUNs.
This ensures that only authorized hosts can access the storage, enhancing security and access control.
For more details, refer to:
* NetApp Documentation on iGroups (NetApp).
NEW QUESTION # 24
A NetApp AFF node in a four-node cluster has a single FC port on one node, which Is used for legacy tape backup. Tape is no longer needed, and the port is disconnected and modified for reuse in the FCP SAN.
Based on this change, which command will verify that the port is usable?
- A. vserver fcp initiator show
- B. lun persistent-reservationshow
- C. networkinterface show
- D. syszem node hardware unified-connect show
Answer: D
Explanation:
To verify that a modified FC port is usable after it has been repurposed from tape backup to FCP SAN, the command system node hardware unified-connect show should be used. This command checks the status and configuration of the unified connect hardware, ensuring that the port is correctly set up for the new function in the SAN environment.
For additional details, see:
* NetApp Command Reference
NEW QUESTION # 25
Which NetApp feature presents LUNs only within the HA pair?
- A. Consistency group
- B. Subsystem
- C. igroup
- D. Selective LUN Mapping
Answer: D
Explanation:
Selective LUN Mapping (SLM) is the feature that presents LUNs only within the HA pair. SLM allows administrators to control which LUNs are visible to which hosts, ensuring that LUNs are only accessible through the designated HA pair, thus improving security and manageability.
For more information, see:
* NetApp Documentation on Selective LUN Mapping
* NetApp Community on LUN Mapping
NEW QUESTION # 26
What configuration must be applied for NVMe/FC?
- A. Create multiple initiator zones and multiple target zones.
- B. Enable NPIV on all fabric switches.
- C. Enable NPV on all fabric switches.
- D. Configure igroup and IQN mapping.
Answer: B
Explanation:
When configuring NVMe/FC (NVMe over Fibre Channel), it is necessary to enable N_Port ID Virtualization (NPIV) on all fabric switches. NPIV allows multiple Fibre Channel initiators to share a single physical Fibre Channel port, which is crucial for NVMe/FC environments where efficient utilization of available ports is needed.
NPIV support enables the creation of virtual ports, which can significantly optimize the configuration and management of Fibre Channel fabrics, thus supporting NVMe/FC operations.
For further details, you can refer to:
* NetApp Community - NVMe/FC Configuration (NetApp Community).
* NetApp Documentation - NVMe Overview (NetApp).
NEW QUESTION # 27
A storage administrator recently implemented ISCSI SAN in a customer environment. Which two actions should be done to ensure the best performance? (Choose two.)
- A. Zone the host by using the host WWPNs.
- B. Decrease the default queue depth on the host to eight.
- C. Connect host and storage ports to the same switches.
- D. Configure Jumbo frames In the entire data path.
Answer: C,D
Explanation:
To ensure the best performance in an iSCSI SAN implementation:
* Connect host and storage ports to the same switches: This minimizes latency and maximizes the efficiency of data paths by ensuring direct connections within the same network segment.
* Configure Jumbo frames in the entire data path: Setting a larger Maximum Transmission Unit (MTU) size reduces the overhead for processing each packet, thus improving overall network performance. Ensuring Jumbo frames are configured end-to-end in the data path is crucial for optimal
* performance.
For further details, check:
* NetApp Best Practices for iSCSI
* NetApp Community Discussion on iSCSI Performance
NEW QUESTION # 28
An administrator has a NetApp AFF cluster with two SVMs serving LUNs. SnapMirror active sync is configured, and a disaster recovery test is planned over the weekend.
Which NetApp ONTAP command will show the status of this test?
- A. network interface failover-groups show
- B. snapmirror failover show
- C. storage failover hwassist show
- D. snapnirror config-replication status show
Answer: B
Explanation:
To check the status of a SnapMirror active sync disaster recovery test on a NetApp ONTAP cluster, you would use the command snapmirror failover show. This command provides the necessary details about the failover status, helping administrators verify if the disaster recovery test is proceeding as expected. It displays the status of the failover groups and their readiness, which is essential for confirming the effectiveness of the disaster recovery setup.
For more detailed information on SnapMirror commands and their usage, refer to:
* NetApp Documentation - SnapMirror Commands (NetApp Community) (NetApp Community).
NEW QUESTION # 29
A customer wants to enable CHAP authentication on their iSCSI sessions.
Which command should be used to set up the appropriate security policies and passwords?
- A. security login create
- B. igroup initiator modify
- C. security certificate create
- D. vserver iscsi security create
Answer: D
Explanation:
To enable CHAP (Challenge-Handshake Authentication Protocol) authentication on iSCSI sessions, the command vserver iscsi security create should be used. This command sets up the necessary security policies and passwords required for CHAP authentication, ensuring secure access to iSCSI targets.
For more details, refer to:
* NetApp Documentation on iSCSI Configuration (NetApp).
NEW QUESTION # 30
A customer has a two-node NetApp AFF ASA cluster in an environment with a Cisco Fibre Channel SAN and Cisco UCS Servers. The customer wants to upgrade the UCS Server BIOS and the Cisco NX-OS system running on the switches.
Which NetApp resource should be consulted to check compatibility with the new versions?
- A. Hardware Universe
- B. BlueXP digital advisor
- C. Active IQ Config Advisor
- D. Interoperability Matrix Tool (IMT)
Answer: D
Explanation:
When planning to upgrade the UCS Server BIOS and Cisco NX-OS system running on the switches in a NetApp AFF ASA cluster environment, theInteroperability Matrix Tool (IMT)is the recommended resource to check compatibility with the new versions. The IMT provides detailed compatibility information for various hardware and software components, ensuring that the planned upgrades will not cause any interoperability issues.
For further details, refer to:
* NetApp Interoperability Matrix Tool
NEW QUESTION # 31
An administrator configured an SVM with LUNs with two WWPNs per node. The administrator accidentally created a WWPN on node1that needs to move to node2. The SAN hosts use ALUA.
Based on this requirement, what must be taken offline to correct the situation?
- A. SVM
- B. Volume
- C. LUN
- D. LIF
Answer: D
Explanation:
To move a WWPN from node1 to node2 in a NetApp ONTAP SAN environment where ALUA is used, you must take the Logical Interface (LIF) offline. Modifying LIFs involves changing their assignment between nodes, which requires them to be temporarily offline. This ensures that the path states are correctly updated without causing disruption to the SAN hosts.
For more details, see:
* NetApp Community on Moving LIFs
* NetApp Documentation on SAN LIFs
NEW QUESTION # 32
A customer has created an SVM for their SAN workloads. They now want to configure the SVM to use NVMe/FC. Which two steps are needed to accomplish this task? (Choose two.)
- A. Create the FC service.
- B. Create the NVMe service.
- C. Add the FC protocol.
- D. Create an NVMe/FC LIF.
Answer: C,D
Explanation:
To configure an SVM to use NVMe/FC, the following steps are necessary:
* Add the FC protocol: This step involves enabling the Fibre Channel protocol on the SVM, which is required to support NVMe over Fibre Channel.
* Create an NVMe/FC LIF: Logical Interfaces (LIFs) must be created to handle NVMe traffic over the Fibre Channel network. These LIFs enable the NVMe namespace access to the host systems.
These steps ensure that the SVM is correctly set up to use NVMe/FC, allowing for efficient and high-performance access to NVMe storage.
For more information, refer to:
* NetApp NVMe/FC Configuration
NEW QUESTION # 33
During maintenance of A NetApp AFF ONTAP cluster, which two steps are needed to move the SAN UFs to new nodes that are members of a portset? (Choose two.)
- A. Disable the SLM feature for the node that hosts the LIF.
- B. Remove the LIF from the portset.
- C. Disable the zoning of the LIF WWPN.
- D. Take the SAN LIF offline.
Answer: B,D
NEW QUESTION # 34
A customer Is setting up a two-node cluster to serve (SCSI LUNs. How many interfaces should be created?
- A. Two iSCSI LIFs per node
- B. One iSCSI LIF per node
- C. Two ISCSI LIFs per SVM
- D. One ISCSI LIF per SVM
Answer: A
Explanation:
For a two-node cluster serving iSCSI LUNs, it is recommended to createtwo iSCSI LIFs per node. This configuration provides redundancy and load balancing, ensuring that each node can handle failover scenarios effectively and maintain high availability for the iSCSI connections.
For more details, see:
* NetApp Documentation on iSCSI LIF Configuration
NEW QUESTION # 35
When using tagged VLANs on Cisco Nexus switches for NVMe over TCP, which two changes must be made to enable jumbo frames? (Choose two.)
- A. Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9216.
- B. Modify the Cisco Nexus switches to use an MTU of 9000.
- C. Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9000.
- D. Modify the Cisco Nexus switches to use an MTU of 9216.
Answer: A,D
Explanation:
For enabling jumbo frames on Cisco Nexus switches for NVMe over TCP with tagged VLANs, the following changes are required:
* Modify the Cisco Nexus switches to use an MTU of 9216: Setting the MTU to 9216 ensures that the network can handle jumbo frames, reducing the number of packets needed for large data transfers and thus improving performance.
* Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9216:
This setting must match the network configuration to ensure end-to-end support for jumbo frames, which is essential for optimizing performance in NVMe over TCP environments.
For additional information, refer to:
* NetApp Documentation on NVMe over TCP
* Cisco Documentation on Jumbo Frames
NEW QUESTION # 36
A LUN Is displaying 90% used space in the NetApp ONTAP CLI, but a Windows Server shows only 10% used space.
What is the first step to take to address this issue?
- A. Disable automatic resizing.
- B. Disable space allocation.
- C. Enable automatic resizing.
- D. Enable space allocation.
Answer: D
Explanation:
When a LUN shows 90% used space in the NetApp ONTAP CLI but a Windows Server shows only 10% used space, the discrepancy is often due to how space allocation is handled between the two systems. Enabling space allocation ensures that the ONTAP system accurately reflects the actual space usage as reported by the host system, in this case, the Windows Server. This adjustment allows ONTAP to reclaim and manage space more effectively, aligning the reported usage between the ONTAP system and the host.
For more information, refer to:
* NetApp Community Discussion on Space Allocation
* NetApp Documentation on Space Usage
NEW QUESTION # 37
An administrator is setting up a NetApp ONTAP AFF system for both NVMe/TCP and iSCSI. Which task is required for SAN configuration?
- A. Configure CHAP authentication.
- B. Configure IPsec.
- C. Configure LIFs.
- D. Configure DH-HMAC-CHAP authentication.
Answer: C
Explanation:
When setting up a NetApp ONTAP AFF system for both NVMe/TCP and iSCSI, a critical task required for SAN configuration is to configure Logical Interfaces (LIFs). LIFs are necessary for network connectivity and are used by both NVMe/TCP and iSCSI protocols to communicate between the storage system and the host.
The configuration of LIFs involves creating and managing these interfaces to ensure they are correctly mapped and available for use by the respective protocols. This step is essential for the SAN setup to function properly.
For more detailed steps on configuring LIFs, you can refer to NetApp's documentation:
* How to Configure NVMe/TCP with ONTAP (NetApp Community).
* SAN Configuration with ONTAP (NetApp).
NEW QUESTION # 38
......
Network Appliance NS0-521 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
| Topic 8 |
|
Accurate & Verified New NS0-521 Answers As Experienced in the Actual Test!: https://www.actualtestsquiz.com/NS0-521-test-torrent.html
Valid NS0-521 Test Answers Full-length Practice Certification Exams: https://drive.google.com/open?id=1DuWOP40JwdOPOqODgXi9rzQqj5mAKAcK
